tomkandula | tone stack calculator


Tone Stack Calculator

Analogue tone stacks, drawn and measured

Illustration

Pick a circuit, change the components and the potentiometers, and watch the frequency response update. Every result is calculated by the Electronics API from the original Maxima model.

Jump to the calculator

What a tone stack actually does

A tone stack is a passive network of resistors and capacitors that sits between two amplifier stages. It has no gain of its own: every boost you hear is really the other frequencies being cut. Turning a control moves a wiper along a potentiometer, which changes the resistance the capacitors see and shifts the corner frequencies of the filter. That is why the controls interact — pull the middle down and the treble control starts to behave differently, because it is the same handful of parts responding to both changes.

The curve is calculated, not drawn

Each circuit here is a real schematic rather than an EQ preset. Its transfer function was derived symbolically with Maxima, and the server evaluates that exact expression at every point on the chart: 10 Hz to 100 kHz, 90 points per decade, on a logarithmic frequency axis. Nothing is sampled from a lookup table and nothing is smoothed to look right. Change a resistor from 47k to 22k and the curve moves exactly as the equation says it should.

How one calculation runs

  1. Your component values are parsed, validated and sent to the Electronics API as SI numbers.
  2. Each potentiometer is split into two resistors at the position set by its rotation and its taper.
  3. The circuit's matrix is evaluated at every frequency in the grid, and the transfer function is solved for each point.
  4. Magnitude is converted to decibels and phase to degrees; both series come back together for the chart.

Reading the amplitude plot

The vertical axis is gain in decibels. Zero means the signal passes unchanged, and every -6 dB is a factor of two in voltage — a stack sitting at -20 dB across the band is passing roughly a tenth of the input. A passive tone stack mostly cuts, and the controls decide where the cuts land. A treble control does not so much boost highs as stop removing them, which is why the curve at full treble is closer to flat and at minimum treble slopes down toward the right.

Reading the phase plot

Phase is the delay the network imposes at each frequency, in degrees. A single RC section can shift up to 90°; a stack with several capacitors can swing through a few hundred degrees across the band. Phase on its own is not what you hear, but it shows where the filter actually turns over, and it matters when the stack is combined with other stages. The button above the chart switches the same calculation between amplitude and phase.

Values and controls

Component values take shorthand: 4k7, 470n, 2.2u, 1meg. The calculator parses the notation and sends SI values — ohms and farads — to the server, which validates them again against the range allowed for that part. Bare numbers fall back to the unit for the part type: ohms for a resistor, picofarads for a capacitor. Values must be positive, and a value outside the usable range is rejected before any calculation runs.

A potentiometer is modelled as two resistors that meet at the wiper. Rotating it moves the split point, and the taper decides how rotation maps onto resistance. A linear taper divides evenly; logA, logB and logC follow the common audio-taper curves, where the same physical position can produce very different resistance ratios. Two pots of the same value will give different curves at the same dial position if their tapers differ.

Snapshots: compare before and after

The curve updates while you drag a control. When you find a setting worth keeping, take a snapshot: it pins the current curve to the chart so you can change the controls and see both at once. Up to eight snapshots are kept; clearing them leaves a single live trace. It is the quickest way to answer questions such as how much bass the middle control really removes when the treble is all the way up.

What the model leaves out

This is a small-signal model of the passive network, with ideal components, an ideal source and an ideal load. It does not include the tube or transistor stages around the stack, output-transformer and speaker impedance, capacitor ESR, pot tolerance or stray wiring capacitance. A real amplifier will differ in the details — most noticeably at the extremes of each control, where the following stage loads the network and moves its corners. The chart describes the filter itself, which is the part you are adjusting.

Show your work

The Maxima derivation behind each circuit is available under the chart. Open it to see the matrices, the symbolic solve, and the expression the server evaluates. The same equations run on every request; the derivation is not a reconstruction made afterwards.